Nabertherm LHT 03/17 D Sintering
These high-temperature furnaces are ideally suited for sintering bridges and crowns made of translucent zirconia. The special heating elements made of molybdenum disilicide promise very good protection against chemical interaction between the charge and the furnace components. The bridges and crowns are loaded in ceramic saggars. These high-temperature furnaces are particularly convincing due to their very good price-performance ratio. The furnaces can be individually programmed for all recommended sintering curves by almost all zirconium manufacturers.
• Tmax 1650 °C
• Furnace chamber with a volume of 1 or 4 liters
• Special heating elements made of molybdenum disilicide offer very good protection against chemical interaction between charge and heating elements
• Dual shell housing made of textured stainless steel sheets with additional fan cooling for low surface temperature
• Exclusive use of insulation materials without categorization according to EC Regulation No. 1272/2008 (CLP)
• Compact design with lift door, opening upwards
• Scope of delivery includes a starter set for charging on one level, additional levels as additional equipment
• Adjustable air inlet
• Furnace chamber can be charged with up to two (LHT 01/17D) or three (LHT 03/17D) saggars, 15 or 25 individual crowns per level (depending on model)
• Exhaust air opening in the roof
• Type S thermocouple
• Precise temperature control, also in the lower temperature range for drying
• Controller P480 (LHT 01/17 D) or P470 (LHT 03/17 D) with memory for 50 programs
• Switchgear with steady control of the heating elements
• Freely usable for sintering blanks of almost all leading manufacturers
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive
These high-temperature furnaces are ideally suited for sintering bridges and crowns made of translucent zirconia. The special heating elements made of molybdenum disilicide promise very good protection against chemical interaction between the charge and the furnace components. The bridges and crowns are loaded in ceramic saggars. These high-temperature furnaces are particularly convincing due to their very good price-performance ratio. The furnaces can be individually programmed for all recommended sintering curves by almost all zirconium manufacturers.
• Tmax 1650 °C
• Furnace chamber with a volume of 1 or 4 liters
• Special heating elements made of molybdenum disilicide offer very good protection against chemical interaction between charge and heating elements
• Dual shell housing made of textured stainless steel sheets with additional fan cooling for low surface temperature
• Exclusive use of insulation materials without categorization according to EC Regulation No. 1272/2008 (CLP)
• Compact design with lift door, opening upwards
• Scope of delivery includes a starter set for charging on one level, additional levels as additional equipment
• Adjustable air inlet
• Furnace chamber can be charged with up to two (LHT 01/17D) or three (LHT 03/17D) saggars, 15 or 25 individual crowns per level (depending on model)
• Exhaust air opening in the roof
• Type S thermocouple
• Precise temperature control, also in the lower temperature range for drying
• Controller P480 (LHT 01/17 D) or P470 (LHT 03/17 D) with memory for 50 programs
• Switchgear with steady control of the heating elements
• Freely usable for sintering blanks of almost all leading manufacturers
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive
These high-temperature furnaces are ideally suited for sintering bridges and crowns made of translucent zirconia. The special heating elements made of molybdenum disilicide promise very good protection against chemical interaction between the charge and the furnace components. The bridges and crowns are loaded in ceramic saggars. These high-temperature furnaces are particularly convincing due to their very good price-performance ratio. The furnaces can be individually programmed for all recommended sintering curves by almost all zirconium manufacturers.
• Tmax 1650 °C
• Furnace chamber with a volume of 1 or 4 liters
• Special heating elements made of molybdenum disilicide offer very good protection against chemical interaction between charge and heating elements
• Dual shell housing made of textured stainless steel sheets with additional fan cooling for low surface temperature
• Exclusive use of insulation materials without categorization according to EC Regulation No. 1272/2008 (CLP)
• Compact design with lift door, opening upwards
• Scope of delivery includes a starter set for charging on one level, additional levels as additional equipment
• Adjustable air inlet
• Furnace chamber can be charged with up to two (LHT 01/17D) or three (LHT 03/17D) saggars, 15 or 25 individual crowns per level (depending on model)
• Exhaust air opening in the roof
• Type S thermocouple
• Precise temperature control, also in the lower temperature range for drying
• Controller P480 (LHT 01/17 D) or P470 (LHT 03/17 D) with memory for 50 programs
• Switchgear with steady control of the heating elements
• Freely usable for sintering blanks of almost all leading manufacturers
• Defined application within the constraints of the operating instructions
• NTLog Basic for Nabertherm controller: recording of process data with USB-flash drive